Printer Diy Kit

Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts

Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts

Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts   Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts

These mechanical parts kits include all framing, linear motion shafts/belts/bearings, fasteners, and mounts to construct a Wilson 2 Prusa type 3D printer - just assemble with the 3D printed parts set and electronics of your choice! The Wilson 2 is a parametric design, allowing easy re-scaling of axes lengths and motion parts; consequently, we offer custom sized frames to fit your particular build and need. Check out our other auctions for steppers, controls, drivers, and a variety of other parts to complete your project! In this listing we offer up to 600mm sizes on each axis.

The Wilson 2 is an extremely robust design and is capable of being built to such a massive size, but we ask that you make - at the very least - the following design considerations when building your printer and prior to purchasing. The Y-axis (depth/build table) is the cheapest way to increase the overall build volume, and is also the best supported/shows the least sag at long lengths. Additional bearings and mounts, or SC10UU type bearings with pillow blocks for direct mounting (instead of the printed bearing holder/base) are available by request at no extra charge for long Y-length kits. We do not recommend X-axis widths greater than 300-400mm (depending on bed type and print-head weight) without modifying the original Wilson design. Again, sag in the X-axis rods and tendency for wide/heavy build platforms to tip or sag can be problematic. Consider Z-probing the bed to correct for sag, using a remote extruder to eliminate a lot of the weight on the carriage, and/or spacing the Y-axis linear rods out more than originally designed to better support the bed.

A tall Z-axis with small X and Y-axes will make the machine prone to tipping or even walking off your tabletop. If you are printing at high speeds with a heavy print head, consider securing it to the machine solidly to the surface beneath it, and ideally securing or bracing the top of the machine against something capable of reducing vibration as well. We have also received a few inquiries for black anodized 2020 extrusion or substituting 2040 on certain axes to increase rigidity... Along with some folks who want even larger build volume. These options and more are available on a by-request basis, so just let us know what we can do for you!

DON'T NEED THE HARDWARE? WANT TO SWAP FOR OTHER PARTS WE HAVE IN STOCK? 2 - 400mm length 2020 aluminum extrusion (Y-axis), Q.

3 - 330mm length 2020 aluminum extrusion (X-axis), and. 4 - 400mm length 2020 aluminum extrusion (Z-axis)... Reflecting 200mm axes, longer lengths re-sized accordingly.

2 - 400mm length 10mm diameter hard-chromed linear rods (Y-axis). 2 - 370mm length 10mm diameter hard-chromed linear rods (X-axis). 2 - 320mm length 10mm diameter hard-chromed linear rods (Z-axis)... 2 - 300mm length 8mm diameter, 2mm pitch/8mm lead, trapezoidal leadscrews for 200mm Z-axis (longer lengths re-sized accordingly), with brass screw nuts and 5mm to 8mm aluminum spring couplings.

2 Meters GT2-6mm width timing belt with Qty. 2 20 tooth GT2 pulleys (enough for X and Y axes, longer lengths re-sized accordingly). 60 slide-in T-nut for 20 series extrusion (M5 thread, zinc plated), Qty. 60 M5x10 stainless steel socket button head cap screw, Qty. M4x10 socket head cap screw. M4x20 socket head cap screw. 4 M4x25 socket head cap screw.

M3x10 socket head cap screw. M3x14 socket head cap screw. M3x25 socket head cap screw.

M2x16 socket head cap screw, and. WHAT ELSE WILL YOU NEED? Printed parts for framing, electronics (including controller, motors, wires, heatbed/extruder, power supply, and switches), heated bed and extruder parts/hardware/mounts. The item "Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts" is in sale since Friday, April 29, 2016. This item is in the category "Consumer Electronics\Other Consumer Electronics". The seller is "autonomousindustries" and is located in Charlottesville, Virginia. This item can be shipped worldwide.
  • Model: Wilson 2
  • Country/Region of Manufacture: United States
  • MPN: Does Not Apply
  • Brand: Unbranded/Generic
  • Type: Parts Kit

Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts   Wilson 2 Prusa Mechanical Parts, DIY 3D Printer Kit, 2020 extrusion/10mm shafts